Garmin Power Meter Pedals Calibration Error Codes

The Garmin Rally and Vector 3 power meter pedals may display an error code during calibration. The code value can be a combination of two error codes. If you are having problems during calibration and have an error code, find the meaning of the error and the action to solve the issue here in this chart.

  Caution

Do not combine pedal extenders with power meter pedals. Combining pedal extenders with power meter pedals can damage the electronics in the pedals which can cause them not to function.

Error Code Meaning of Error Action to Solve the Error
1 Calibration in Progress on the left pedal Calibration already in progress
2 Calibration timeout on the left pedal Make sure the pedals are stationary and not under load
3 Calibration failure due to a failed upright check on the left pedal Place the bike in an upright position
4 Calibration aborted due to pedaling Make sure the pedals are awake or active by spinning or rotating the crank arm and try again
8 Calibration request could not be sent to the right pedal
16 Calibration request was sent to the right pedal but no response was received
32 Calibration failure due to failed upright check on the left pedal Place the bike in an upright position
64 Installation angle parameters not recognized on the left pedal Make sure the pedals are awake or active by spinning or rotating the crank arm and try again
128 Installation angle parameters timeout on the left pedal
256 Calibration in Progress on the right pedal Calibration already in progress
257 Calibration in Progress
258 Calibration aborted due to pedaling on both pedals in progress Make sure the pedals are stationary, awake, in an upright position, and not under load
259 Calibration failure due to a failed upright check on the left and right pedals in progress
260 Calibration timeout on the left pedal and the right pedal in progress
512 Calibration timeout on the right pedal Make sure the pedals are awake or active by spinning or rotating the crank arm and try again
513 Calibration aborted due to pedaling on both pedals in progress Make sure the pedals are stationary, awake, in an upright position, and not under load
514 Calibration aborted due to pedaling Make sure the pedals are stationary and not under load
515 Calibration failure due to a failed upright check on the left and right pedals in progress Make sure the pedals are stationary, awake, in an upright position, and not under load
516 Calibration timeout on the left pedal and the right pedal in progress
768 Calibration failure due to failed upright check on the right pedal Place the bike in an upright position
769 Calibration failure due to a failed upright check on the right pedal and in progress on the left pedal Make sure the pedals are stationary, awake, in an upright position, and not under load
770 Calibration failure due to a failed upright check on the right pedal and pedaling on the left pedal
771 Calibration failure due to a failed upright check Place the bike in an upright position
772 Calibration timeout on the right pedal and a failed upright check on the left pedal Make sure the pedals are stationary, awake, in an upright position, and not under load
1024 Calibration aborted due to pedaling on the right pedal Make sure the pedals are stationary and not under load
1025 Calibration timeout on the right pedal and in progress on the left pedal Make sure the pedals are stationary, awake, in an upright position, and not under load
1026 Calibration timeout on the right pedal and pedaling on the left pedal
1027 Calibration timeout on the right pedal and a failed upright check on the left pedal
1028 Calibration timeout Make sure the pedals are awake or active by spinning or rotating the crank arm and try again
4096 Calibration failure due to a failed upright check on the right pedal Make sure the pedals are awake or active by spinning or rotating the crank arm and try again
8192 Installation angle parameters not recognized on the right pedal Make sure the pedals are awake or active by spinning or rotating the crank arm and try again
16384 Installation angle parameters timeout on the right pedal Make sure the pedals are awake or active by spinning or rotating the crank arm and try again

Click here to learn more about calibration of the Garmin power meter pedals.

Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.

Articles in this section

Customer Service Hours:
8:00am - 5:00pm CST Monday to Friday