Console Codes for 3600RC Spinnaker by Stairmaster, Customize and Diagnose

Use these console codes to diagnose an issue you are having or to customize the settings on your Stairmaster 3600RC Spinnaker exercise bike.

Console codes require the unit to be in an "idle" state for the code to be accepted. "Idle" state means the console is not displaying an error or any message that requires data input. The display should basically be freshly powered up, scrolling the EKG or welcome message.

 

The following console codes are for use with C3, C4, and C5 consoles with Red LEDs.
Level ^, 105, ENTER Clears the custom programmed scrolling message
Level ^, 107, ENTER, 0 Display test
Level ^, 107, ENTER, 1 Speaker test
Level ^, 107, ENTER, 2 Keypad test
Level ^, 107, ENTER, 3 Speed test - Displays Target value and RPM. Need to exercise on the machine and verify value in RPM.
Level ^, 107, ENTER, 4 Software revision test
Level ^, 1746, ENTER Set the address numbers for the GROUP RACE setup
Level ^, 2121, ENTER Turns on the custom scrolling message
Level ^, 2123, ENTER Turns off the custom scrolling message
Level ^, 7424, ENTER Changes the language of the console prompts
Level ^, 7607, ENTER Turns on the custom message option
Level ^, 7607, ENTER, 99 Text bar scrolling message editing function
Level ^, 7703, ENTER Displays machine usage information
Level ^, 9760, ENTER Allows you to change the units displayed by the console
0, ENTER
Changes the console to English units
1, ENTER
Changes the console to metric units

 

The following console codes are for use with C40 consoles with blue LCDs.
Level ^, 30, ENTER Change workout time limit
Level ^, 31, ENTER Change units
Level ^, 32, ENTER Choose type of heart rate input
Level^, 34, ENTER Choose console language
Level ^, 35, ENTER Change contrast
Level ^, 37, ENTER Turn clinical mode on or off
Allows RPM <40, requires battery charger when in this mode
Level ^, 39, ENTER Reset to factory defaults
Level ^, 40, ENTER Display machine run time in hours
Level ^, 41, ENTER Display number of workouts
Level ^, 42, ENTER Display distance traveled
Level ^, 43, ENTER Display software revision
Level ^, 44, ENTER Display machine type
Level ^, 46, ENTER Display machine run time in hours since last cleared (used for maintenance purposes)
Level ^, 60, ENTER Test display - Screen alternates between all LCD segments turned on and a representative program screen
Level ^, 61, ENTER Test keyboard - Pressing any key displays that key's name in the display window. Press CLEAR last to exit.
Level ^, 62, ENTER Test serial port
Level ^, 63, ENTER Test alternator - Verifies alternator field routines through the console. Position yourself on the machine and press ^ for "field on". After briefly exercising you should build resistance. Press V for "field off".
Level ^, 66, ENTER Test tach response - Begin exercising on the machine. Console should regulate the alternator resistance based on the tach signal to maintain approx. 2,000 RPMs while you are exercising. If not, there is a possible problem in the AC Tap (TACH) or field circuit – check the alternator, AC Tap (Tach) wire, the field wire, the diode, the terminal posts, and the main cable.
Level ^, 71, ENTER Reset service time
Level ^, 80, ENTER Change machine type
Level ^, 81, ENTER Change Bike Gear – "24/1 prior to 10/98" or "30/1 after 10/98"
Level ^, 90, ENTER StairMaster Fit Test
Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Please sign in to leave a comment.

Articles in this section

See more
Customer Service Hours:
8:00am - 5:00pm CST Monday to Friday